Showing results: 796 - 810 of 1660 items found.
-
Qualitest International Inc.
Our Freezing Tester units are available in vertical or horizontal configurations are used to test the bending/flexing durability of rubber, plastics, synthetic leather, shoes, etc., under cold temperatures as low as -30°C or -70°C depending on the selected model. The test chambers can be equipped with a variety of flexing/bending fixtures made of stainless steel. These models conform to ASTM D 1790, and ASTM D1593 standards.
-
264 -
SCI
Our 264 Model makes Ground Bond / High Continuity Testing simple with 40 Amps of current to satisfy your NRTL standard. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 264 can easily be deployed in both laboratory and production line environments. Ensure every Ground Bond Test is accurate with our Milliohm offset function.
-
266 -
SCI
Our 266 Model makes Ground Bond / High Continuity Testing simple with 60 Amps of current to satisfy your toughest NRTL standard. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 266 can easily be deployed in both laboratory and production line environments. Ensure every Ground Bond Test is accurate with our Milliohm offset function.
-
KRD31 series -
CME Technology Co. Ltd.
KRD31 series constant acceleration tester are used to test articles under extreme acceleration conditions based on standard like MIL-STD-810F, MIL-STD-202 and IEC68-2-7. It is most suitable for testing electronic components or devices. Under high g effect on microcircuits, to check adaptability and reliability of wiring and the internal structures. It may expose mechanical and structural defects that are not found with vibration and shock tests.
-
FSMR3000 -
Rohde & Schwarz GmbH & Co. KG
The R&S®FSMR3000 is a microwave measurement receiver to calibrate signal generators and attenuators with one single instrument. Most important features provided are tuned RF level measurements, level measurements, analog modulation and spectrum analysis. Additionally, the R&S®FSMR3000 can be equipped with powerful hardware for high-end phase noise test supplementary to the standard phase noise test with the spectrum analyzer.
-
C&S group GmbH
No matter whether you have developed a product without an underlying standard or extended a product beyond the standard – we verify your product to see if it conforms to the characteristics specified by you. We advise you on worst-case scenarios.You need a test under certain temperature conditions? We have the possibility to execute appropriate temperature tests.You have other testing needs? Please contact us so we can consult you thereto and submit an offer.
-
Fluke Calibration
Fluke calibration offers digital pressure monitors, air data calibrators and laboratory standards for air data pressure range calibrations. Each of these systems feature pressure ranges, measurement units and features specific to calibrate air data test sets and RVSM compliant air data instruments. Models include 2468 Ruska and ADCS-601 DHI primary level standards; 7750i Ruska air data controller/calibrator and RPM4-AD DHI reference pressure monitor.
-
Morris Products Inc.
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
NI
The PXI FlexRIO Digital I/O Module leverages standard digital I/O with a flexible, user-defined FPGA to solve a variety of challenges, from high‐speed communication with a device under test (DUT) to emulating custom protocols in real time. You can use the PXI FlexRIO Digital I/O Module for real-time interfacing of standard protocols or implementing customized protocols. Additionally, the module features multiple directional and FPGA variants to fit different interfacing and application needs.
-
Gauss Instruments
The EMI receiver families TDEMI® of GAUSS INSTRUMENTS® provide a huge fully CISPR compliant real-time bandwidth and therefore allow to speed up your measurements tremendously and to reduce the measurement uncertainty significantly - both at the same time. By using the full automation software suite EMI64k from GAUSS INSTRUMENTS the test procedures according to the CISPR 16-2-3 standard for the FFT-based measuring instruments as well as conventional testing (pre-scan and final maximization) and further EMC Standards are available. In comparison to the previously conventional pre-scan and final measurement strategy, the overall test quality can be significantly increased whereas the testing times are reduced by orders of magnitudes.
-
Emergent Electro-Mechanical
Emergent's fixture kits are available in bottom and double sided probing versions. They are fully scalable, from compact benchtop testers to full size multi-UUT production floor models. The removable, interchangeable plate design allows you to easily add and move test points, or swap out plates to test a completely different product. Each kit comes with a standard linear collapse over-clamp. A cam-follower closing system can be specified for higher force applications. Our fixture kits are manufactured using industrial grade phenolic laminate, which is similar to G10 in hardness and strength but easier to machine. The standard kit comes pre-assembled with blank plates for machining.
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Rosenberger offers a wide range of PCB connectors, which are tailored to the high demands of industrial test applications. The product range includes many common standard RF series, e.g. SMP, WSMP, Mini-SMP, SMA, QMA, SMB, MCX or Mini-Coax, but also innovative coaxial series such as P-SMP, Longwipe-SMP, FMC or Micro-RF.For specific test & measurement applications, Rosenberger develops and produces modular connector systems for DC frequencies up to 50 GHz, solderless PCB mount connectors for ultra-high frequency applications up to 110 GHz or spring-loaded coax systems ( > 2,500 matings, pairwise phase matching 10 ps standard, different cable lengths).
-
Plottergeist -
Aphena Ltd
Plottergeist "the phantom plotter" emulates all the common HPGL plotters. It runs on a standard PC equipped with a GPIB card or using RS-232, and connects to test equipment or another computer. The software behaves like a real plotter, with the exception that the PC screen is the paper.
-
PMT10000 -
Power Measurement Technologies Inc.
High voltage, low dissipation factor, gas-filled Standard Capacitors for indoor use in a laboratory or production environment. A three terminal design configuration allows accurate measurements of capacitance and dissipation factor (tangent delta) with little or no effect from test lead or stray capacitance.
-
SimpleTester -
SimpleSoft Inc.
The SimpleTester™ is the industry leading SNMP test tool that automatically exercises SNMP v1, v2C, and v3 agents. All types of SNMP Agents (standalone, proxies, sub-agents) implementing one or more standard, experimental or private MIBs can be exhaustively tested, within minutes.
